Bricks and Mortar MCQ Quiz - Objective Question with Answer for Bricks and Mortar - Download Free PDF

Explanation:

Types of brick masonry bonds:

Explanation:

Other tools that are used in brick masonry construction:

Brick Hammer: Used for cutting bricks, also for pushing the bricks in courses.

Trowel: Used for lifting and spreading mortar; also for cutting bricks.

Spirit Level: Used, with a straight edge, for getting horizontal surface; also used for leveling.

Plumb rule: Used for checking verticality of brick walls.

Line and Pins: Used for maintaining alignment of courses.

Scutch: Used for cutting soft bricks and dressing out surfaces.

Bolster: Used for accurate cutting of bricks.

Jointer: Used for pointing the joints.

Explanation:

1. The English bond is considered the strongest and most suitable for load-bearing walls due to its construction and arrangement of bricks.
2. It consists of alternating courses of headers (bricks laid flat, with their ends exposed) and stretchers (bricks laid lengthwise).
3. This bond provides excellent strength and stability, making it ideal for structures that will bear heavy loads.

Additional Information

1. Stretcher bond: This bond consists of all bricks laid as stretchers in each course. It is weaker than the English bond because there is no interlocking of headers to provide additional strength. It is more commonly used for non-loadbearing walls or decorative purposes.
2. Flemish bond: In this bond, each course alternates between headers and stretchers. While it is aesthetically pleasing and often used for decorative walls, it is not as strong as the English bond for load-bearing applications.
3. Header bond: This bond consists of all bricks laid as headers, which means only the short ends of the bricks are exposed. While it can be strong in some cases, it is less efficient for load-bearing purposes compared to the English bond. 

Explanation:

According to IS 12894:2002

• The clay and silt content in sand used for pulverized fuel-ash lime bricks should preferably be in the range of 0-5%.
• This helps ensure the proper bonding and workability of the bricks without excessive shrinkage or cracking.

 Additional InformationPulverized Fuel-Ash Lime Bricks (PFAL Bricks)

These bricks are made by using pulverized fuel ash (PFA), also known as fly ash, which is a by-product of coal combustion in power plants. The process involves mixing PFA with lime and sometimes sand to create durable building materials.

Key Components:

• Pulverized Fuel Ash (PFA): A fine ash generated from coal combustion. It's the primary ingredient in PFAL bricks.

• Lime: Acts as a binding agent to bind PFA particles and provide strength.

• Sand: Sometimes used in small quantities to adjust the texture and workability of the brick mix.

Explanation:

English bond

• When two walls meet at right angles, the English bond is commonly used to ensure structural strength.
• This bond alternates between a course of headers (short sides of bricks) and a course of stretchers (long sides of bricks), which provides strong interlocking between the two walls and enhances their stability.

Additional Information

Flemish bond

• Used primarily for decorative purposes, where each course alternates between headers and stretchers. It is not typically used for walls meeting at right angles.

Header bond

• This bond uses headers (short sides of bricks) at the joint, and while effective for strength, it is less common than English bond for walls at right angles.

Stretcher bond

• Uses only stretchers (long sides of bricks) and is generally used for single brick walls, but it does not provide sufficient interlocking strength for walls meeting at right angles.

1) Weathering is the process of breaking down and loosening the surface minerals of rock so that they can be transported away by agents of erosion such as water, wind and ice.

2) Quarrying is the multistage process by which rock is extracted from the ground and crushed to produce aggregate, which is then screened into the sizes required for immediate use, or for further processing, such as coating with bitumen to make bituminous macadam or asphalt.

3) Dressing of Stone is the working of quarried stone into the shape and size required for use. This can be necessary as stones obtained from quarrying generally do not have the exact required dimensions or finish.

Concept:

Classification and uses of building stones-

A good building stone has the following properties:

• Percentage of wear in the attrition test should not be more than 3
• Specific gravity should be at least 2.7
• Coefficient of hardness should be greater than 17
• Percentage of water absorption by weight of stone should be less than 5
• Toughness index should not be less than 13
• Crushing strength should be greater than 100 N/mm² or MPa.

A good building stone has the following properties:

• The percentage of wear in the attrition test should not be more than 2 for road work.
• Specific gravity should be at least 2.7
• The coefficient of hardness should be greater than 17
• Percentage of water absorption by weight of stone should be less than 5
• The toughness index should not be less than 13
• Crushing strength should be greater than 100 N/mm²

For road works, Wear not more than 2% and for building stone, It should not more than 3%.

Explanation:

Good Brick Earth Constituents table:

Compacted sandstone: It is a type of rock which has the quartz or the sand bound together with the cementing minerals like mica, feldspar etc.

Compacted sandstone has the following properties:

(a) It is a sedimentary rock

(b) Its colour depends upon that of the feldspar

(c) It can be used as a road metal if the higher quality stones like basalt and granite are not available

(d) It is fire resistant

(e) Its specific gravity is 2.25

(f) Its crushing strength varies 35 to 40 MN/m2

Mangalore tiles are a type of tile native to the city of Mangalore, India. These red coloured clay tiles, unique in shape and size. Since these clay tiles are molded under extreme heat, they are resistant to damage or destruction from fire.

Mosaic tile is any combination of materials such as glass, ceramic, porcelain or stone, usually set in a small format and set on a mesh sheet for easy installation. They are used in backsplash, shower, bath or floor.

Slate tile is a type of natural stone which is quarried from the side of mountains or taken from the earth. A finely grained, homogeneous, metamorphic rock, it is named for the way the material forms in plains, like sheets resting on top of the other, compressed under great pressure to create a strong bond.

Explanation:

Floats are used to press mortar and spread it uniformly.

A trowel is a small hand tool used for digging, applying, smoothing, or moving small amounts of viscous or particulate material.

Aluminium rod is used to strike off excess mortar.

A brush is used to clean the mortar. Floats are used to press mortar and spread it uniformly.

Explanation:

Defects in Bricks are:

1. Bloating: This defect observed as spongy swollen mass over the surface of burned bricks is caused due to presence of excess carbonaceous matter and sulphur in brick clay.

2. Chuffs: The deformation of the shape of bricks caused by the rain water falling on hot bricks is known as chuffs.

Concept:

Kneading: It is the process of mixing water with blended clay (clay with additional minerals) to make it plastic.

Kneading of the brick earth occurs after clay has been weathered, and blended and is the last step in the preparation of brick earth before moulding it into the shape.

Kneading is done either manually or by combined kneading-tempering by adding moisture to the already blended soil and placing it in pug mills (often called as clay mixers).

Kneading is done to obtain a homogeneous mass and to develop plasticity for the following moulding process.

Tempering of clay: It is the process of adding water to the clay and allowing it to remain un-disturbed for few days before mixing occurs.

Pugging: It is also the process of working and tempering of clay to make it plastic and consistent.

Moulding: It is the process of giving a required shape to the brick from the prepared brick earth. It can be hand moulded or machine moulded.